	CATALOG DOCUMENTATION
	EMAP-ESTUARIES PROVINCE LEVEL DATABASE
	CAROLINIAN PROVINCE 1994-1997
	SEDIMENT CHEMISTRY DATA


TABLE OF CONTENTS

1.  DATA SET IDENTIFICATION

2.  INVESTIGATOR INFORMATION

3.  DATA SET ABSTRACT

4.  OBJECTIVES AND INTRODUCTION

5.  DATA ACQUISITION AND PROCESSING METHODS

6.  DATA MANIPULATIONS

7.  DATA DESCRIPTION

8.  GEOGRAPHICAL AND SPATIAL INFORMATION

9.  QUALITY CONTROL/QUALITY ASSURANCE

10. DATA ACCESS

11. REFERENCES

12. TABLE OF ACRONYMS

13. PERSONNEL INFORMATION


1.  DATA SET IDENTIFICATION

	1.1 Title of Catalog Document

		EMAP-Estuaries Province Level Database
		Carolinian Province
		Sediment Chemistry Data

	1.2 Authors of the Catalog entry

		Timothy R. Snoots,
		Dr. Jeffrey L. Hyland

	1.3 Catalog Revision Date

		September 10, 1998

	1.4 Data Set Name

		CP_CHM_D.DAT, CP_CHM_A.DAT

	1.5 Task Group

		Estuaries

	1.6 Data set identification codes

		5, 6

	1.7 Version

		001

	1.8 Requested Acknowledgment

		If you plan to publish these data in any way, EPA requires
		a standard statement for work it has supported:

		"Although the data described in this article have been
		funded wholly or in part by the U. S. Environmental
		Protection Agency through its EMAP-Estuaries Program, it
		has not been subjected to Agency review, and therefore does
		not necessarily reflect the views of the Agency and no official
		endorsement should be inferred."


2.  INVESTIGATOR INFORMATION

	2.1 Principal Investigator

		J. Hyland (NOAA/NOS/ORCA) - Carolinian Province Manager
		A. Ringwood (SCDNR) - Lead P.I. for SC/GA region team
		C. Hackney (UNC-W) - Lead P.I. for NC region team
		G. McRae, G. Nelson, J. McKenna, J. Landsberg (FLDEP) -
			Lead P.I.s for FL region team (depending on year)

	2.2 Investigation Participant - Sample Collection

		Field Sample Collection

			T. Alphin, J. Bichy, S. Bowen, C. Byrum, D. Dye, A. Gospodarek,
			J. Grace, J. Grimley, C. Hackney, C. Powell, C. Preziosi,
			H. Riley, S. Roberts, M. Smith, K. Stokesbury,
			D. Tremain, T. Wheeler (UNC-W); S. Ross (NCNERR);
			M. Armstrong-Taylor, J. Jones, M. Levinson, P. Powers,
			A. Ringwood, T. Snoots, G. Steele (SCDNR); L. Balthis,
			T. Herrlinger, C. Keppler, M. Wert (UC); D. Adams,
			K. Amendola, D. Cook, C. Harnden, B. Heagey, J. Mckenna,
			G. Nelson, C. Nowicki, R. Paperno, B. Rosenblatt,
			M. Wessel (FLDEP); J. Hyland, S. Kokkinakis
			(NOAA/NOS/ORCA); 

		Field Training and Coordination

			S. Kokkinakis (NOAA/NOS/ORCA); J. Macauley (EPA-GED);
			T. Heitmuller (USGS-GB); D. Keith (EPA-AED)

	2.3 Sampling Processing - Principal Investigator

		Program Management and Coordination

			J. Hyland, A. Robertson (NOAA/NOS/ORCA); K. Summers (EPA);
			F. Holland, A. Ringwood (SCDNR); C. Hackney,
			T. Wheeler (UNC-W); S. Ross (NCNERR);
			J. Landsberg, J. McKenna, G. McRae, G. Nelson,
			R. Paperno (FLDEP)

		Contaminant Analyses

			P. Boothe, J. Brooks, G. Denoux, B. Presley,
			T. Wade (TAMU/GERG)

		QA/QC

			T. Heitmuller (USGS-GB), S. Kokkinakis (NOAA/NOS/ORCA)

		Data Management and Statistical Support

			T. Snoots, F. Holland, R. VanDolah (SCDNR); L. Balthis,
			T. Herrlinger (UC); J. Rosen, L. Zimmerman (TPMC);
			S. Rathbun (UGA);  M. Adams, L. Harwell (JCWS);
			V. Engle (EPA-GED); Z. Malaeb (USGS-GB);
			S. Hale (EPA-AED); K. Summers (EPA); T. Wilson (CU)


3.  DATA SET ABSTRACT

	3.1 Abstract of the Data set

		The CP_CHM_D.DAT data set reports a suite of chemical
		concentrations from analyses of a surface sediment sample
		(upper 2-3 cm) composited from multiple grabs at each sampling
		station in the Carolinian Province from 1994-1997.  Individual
		and analyte group summary concentrations are reported.   A total
		of 17 inorganic trace elements, 4 butyltins, 27 aliphatic
		hydrocarbons, 44 polynuclear aromatic hydrocarbons (PAHs), 20
		polychlorinated biphenyls (PCBs), 23 pesticides, Total Organic
		Carbon (TOC), and several summary (totals) concentrations are
		reported for each station.

		The CP_CHM_A.DAT data set reports full descriptive analyte names
		for each of the ANAL codes used to represent analytes in the
		CP_CHM_D.DAT data set.

		The following reports are products of these and other data
		collected during the 1994-1997 Sampling period in the Carolinian
		Province.  These reports may contain additional information and
		summary statistics that are not contained in this data set
		catalog or its respective data sets.  We therefore recommend
		referring to them when using these data.

		Hyland, J.L., T.J. Herrlinger, T.R. Snoots, A.H. Ringwood, R.F.
			Van Dolah, C.T. Hackney, G.A. Nelson, J.S. Rosen, and
			S.A. Kokkinakis.  1996.  Environmental quality of
			estuaries of the Carolinian Province: 1994. Annual
			statistical summary for the 1994 EMAP-Estuaries
			Demonstration Project in the Carolinian Province.
			NOAA Technical Memorandum NOS ORCA 97.  NOAA/NOS,
			Office of Ocean Resources Conservation and Assessment,
			Silver Spring, MD. 102 p.

		Hyland, J.L., L. Balthis, C.T. Hackney, G. McRae, A.H. Ringwood,
			T.R. Snoots, R.F. Van Dolah, and T.L. Wade.  1998.
			Environmental quality of estuaries of the Carolinian
			Province: 1995. Annual statistical summary for the 1995
			EMAP-Estuaries Demonstration Project in the Carolinian
			Province.  NOAA Technical Memorandum NOS ORCA 123
			NOAA/NOS, Office of Ocean Resources Conservation and
			Assessment, Silver Spring, MD. 143 p.

		Balthis, W.L., J.L. Hyland, and T.R. Snoots.  1998.  Compendium of
			environmental data for estuaries sampled in the North Carolina
			portion of the EMAP Carolinian Province during summer 1994-1996.
			Unpublished report, May 1998.  62 p.

		See Also: GERG (1995a), GERG (1995b), GERG (1996), GERG (1997a),
			GERG (1997b), GERG (1998).

	3.2 Keywords for the Data Set

		CP_CHM_D.DAT

		Sediment contaminants, sediment chemistry, DDT, inorganic analytes,
		organic analytes, PAH, PCB, pesticides, TOC, trace metals, butyltin,
		EMAP Carolinian Province

		CP_CHM_A.DAT

		Sediment contaminants, analyte codes, analyte names,
		EMAP Carolinian Province


4.  OBJECTIVES AND INTRODUCTION

	4.1 Program Objective

		EMAP has three primary objectives:

		1.  To estimate the current status, extent, changes, and trends
			in indicators of the Nation's ecological resources on a
			regional basis;

		2.  To monitor indicators of pollutant exposure and habitat
			condition, and to seek correlative relationships between
			human-induced stresses and ecological condition that
			identify possible causes of adverse effects; and

		3.  To provide periodic statistical summaries and interpretive
			reports on ecological status and trends to the EPA
			Administrator and to the public. 

	4.2 Data Set Objective

		The objective of the CP_CHM_D.DAT data set is to report the
		results of sediment contaminant analyses at each of the stations
		sampled in the Carolinian Province from 1994-1997.

	4.3 Data Set Background Information

		Contaminant and TOC concentrations were measured at each station
		from subsamples of composited surface sediment (upper 2-3 cm)
		collected with a 0.04-m2 Young grab sampler.  Subsamples were
		taken from the same sediment composite used for toxicity testing
		and the analysis of other physical/chemical characteristics.
		Multiple grabs were taken at each station to produce enough
		composited surface sediment to support all of the various kinds
		of sediment analyses.  Stations were represented usually by
		unreplicated samples, with the exception of duplicates that were
		run for ~ 10% of the stations as part of the quality control
		program.

		All contaminant analyses were performed at Texas A&M University.
		A total of 17 inorganic metals, 4 butyltins, 27 aliphatic
		hydrocarbons, 44 polynuclear aromatic hydrocarbons (PAHs),
		20 polychlorinated biphenyls (PCBs), and 23 pesticides, total
		organic carbon (TOC), and several summary (totals) concentrations
		were measured at each of the stations sampled in the Carolinian
		Province from 1994-1997.  The table that follows summarizes the
		measurement units, target detection limits, analytical methods,
		and protocol references for each of these analyte groups.

		Summary of analytical methods for the analyses of contaminants
		in sediments.
		----------------------------------------------------------------
		Analyte  Target DL   Units    Method      Reference
		----------------------------------------------------------------
		Si       10,000      g/g     FAA        Taylor and Presley 1993
		Al         1500      g/g     FAA        Taylor and Presley 1993
		Fe          500      g/g     INAA       Taylor and Presley 1993
		Cr            5.0    g/g     INAA       Taylor and Presley 1993
		Zn ('94-'96)  2.0    g/g     FAA        Taylor and Presley 1993
		Zn (in 1997)  2.0    g/g     INAA       Taylor and Presley 1993
		Mn            1.0    g/g     FAA        Taylor and Presley 1993
		Cu            5.0    g/g     GFAA       Taylor and Presley 1993
		As            1.5    g/g     INAA       Taylor and Presley 1993
		Ni            1.0    g/g     GFAA       Taylor and Presley 1993
		Pb            1.0    g/g     GFAA       Taylor and Presley 1993
		Sb            0.2    g/g     INAA       Taylor and Presley 1993
		Se (in 1994)  0.1    g/g     INAA       Taylor and Presley 1993
		Se ('95-'97)  0.1    g/g     GFAA       Taylor and Presley 1993
		Sn            0.1    g/g     GFAA       Taylor and Presley 1993
		Cd            0.05   g/g     GFAA       Taylor and Presley 1993
		Ag            0.01   g/g     GFAA       Taylor and Presley 1993
		Hg            0.01   g/g     CVAA       Taylor and Presley 1993
		Butyltins     1.0    ng Sn/g  GC/FPD     Wade et al. 1990
		PAHs          5.0    ng/g     GC/MS-SIM  Wade et al. 1993
		Aliphatics   25      ng/g     GC/FID     Wade et al. 1994
		Pesticides    0.1    ng/g     GC/ECD     Wade et al. 1993
		PCBs          0.1    ng/g     GC/ECD     Wade et al. 1993
		----------------------------------------------------------------
		Notes:
		* Units are based on dry wt.
		* target DL = Minimum allowable detection limits (based on sample
		  size of 0.2 g for metals and 15 g for organics).
		* GC/ECD = Gas Chromatography/Electron Capture Detection
		* GC/MS-SIM = GC/Mass Spectroscopy - Selective Ion Monitoring Mode
		* GC/FID = GC/Flame Ionization Detection
		* CVAA = Cold Vapor Atomic Absorption
		* GFAA = Graphite Furnace Atomic Absorption
		* INAA = Instrumental Neutron Activation Analysis
		* FAA = Flame Atomic Absorption
		* GC/FPD = GC/Flame Photometric Detection.
		* Butyltins: mono-, di-, tri-, tetra-
		* PAHs: 44 parent compounds & alkylated homologues, Tot. PAHs
		* Aliphatics: C10C34 alkanes, Tot. Alk., pristane, phytane
		* Pesticides: DDD (2,4'& 4,4'), DDE (2,4' & 4,4'), DDT (2,4' & 4,4'),
		  Total DDD/DDE/DDT, aldrin, chlordane (alpha-, gamma-, oxy-),
		  dieldrin, heptachlor, heptachlor epoxide, hexachlorobenzene,
		  BHC (alpha-, beta-, gamma-, delta-), mirex, trans- &
		  cis-nonachlor, endrin, endosulfan, toxaphene
		* PCBs: Congener Nos. 8, 18, 28, 44, 52, 66, 77/110, 101, 105,
		  188/108/149, 126, 128, 138, 153, 170, 180, 187/182/159, 195, 206,
		  209, Tot. PCBs

		Measurements of TOC were obtained from ~ 5 to 10 mg samples of
		dried sediment that were acidified (with 1M H3PO4) to remove
		carbonates, sonicated, and filtered.  Filters containing the
		sediment were dried and combusted (Salonen 1979) on either a CHN
		or elemental analyzer to determine TOC concentration (expressed
		as percent TOC per gram of dried sediment).  TOC analyses were
		performed by different labs depending on year and station
		location.  In 1994, each cooperator analyzed samples from their
		respective regions (i.e., UNC-W analyzed all stations from NC,
		SCDNR analyzed all stations from SC and GA, and FLDEP analyzed
		all stations from FL).  In 1995, SCDNR analyzed all stations
		from NC, SC and GA, and FLDEP analyzed all stations from FL.
		In 1996 and 1997, all TOC analyses wer performed by GERG, with
		the exception of Chowan River samples (CP97345-CP97354) which
		were analyzed by EPA.

	4.4 Summary of Data Set Parameters

		A code for each compound is given under the variable ANAL.
		Concentrations are reported in dry weight, in the variable CONC.
		The units of the results reported in CONC are reported in the
		variable called UNIT.  Quality Assurance/Quality Control issues
		are coded and reported in the variable called QA.  QA code
		descriptions are given in section 5.2.4 (Sample Processing Quality
		Control) of this file.  Method detection limits for each analysis
		are reported in the variable DETLMT.

	4.5 Year-Specific Information about Data


5.  DATA ACQUISITION AND PROCESSING METHODS

	5.1 Data Acquisition

		5.1.1 Sampling Objective

			Collect sediment samples suitable for the analysis of organic
			and inorganic compounds, and TOC.  One composite sediment
			sample was expected to be collected at each station.

		5.1.2 Sample Collection Method Summary

			A 1/25 m2, Kynar-coated stainless steel, Young Grab sampler
			was used to collect sediments. This grab sampled an area of
			440 cm2 and a maximum depth of penetration in the sediment
			of 10 cm.  Stainless steel utensils were used to remove the
			top two cm of sediment from a grab.  The sediment was removed
			to a stainless steel bowl and placed in a cooler of ice to
			remain cold, but unfrozen.  The grab sampler was rinsed and
			re-deployed. This procedure was repeated until the volume of
			sediment required for all contaminant, toxicity, and sediment
			characteristics analyses had been collected..  The sediment
			was mixed by hand until thoroughly homogenized, and aliquots
			were placed immediately into pre-cleaned glass jars
			(for organics) or plastic containers (for inorganics).  The
			samples were immediately stored on ice following collection.

		5.1.3 Beginning Sampling Dates

			30 June 1994
			05 July 1995
			09 July 1996
			07 July 1997

		5.1.4 Ending Sampling Dates

			31 August 1994
			14 September 1995
			19 September 1996
			25 August 1997

		5.1.5 Platform

			Samples were collected from various gasoline or diesel
			powered boats equipped with at least the following
			equipment:  "A" frame boom or davit, winch, LORAN-C or
			GPS for location, and a depth finder.

		5.1.6 Sampling Equipment

			A 1/25 m2, Kynar-coated stainless steel, Young Grab sampler.
			This grab sampled an area of 440 cm2 and a maximum depth
			of penetration in the sediment of 10 cm.

		5.1.7 Manufacturer of Sampling Equipment

			Ted Young
			Falmouth, MA

		5.1.8 Key Variables

		5.1.9 Sample Collection Method Calibration

			The sampling gear does not require any calibration.
			It required inspection for deformities incurred due to
			mishandling or impact on rocky substrates.

		5.1.10 Sample Collection Quality Control

			Field technicians were trained to follow Standard Operating
			Procedures to insure the collection of representative,
			uncontaminated and high quality samples.  QA/QC measures
			were taken in the field to avoid or reduce contamination
			and insure the collection of representative samples.  These
			included: use of stainless steel instruments, thorough
			cleaning of the sampler between grabs, use of pre-cleaned
			containers for sediment storage and ensuring that engines
			were shut down when a sample was exposed to the air.
			A successful grab had relatively level, intact sediment over
			the entire area of the grab and a sediment depth of 7-10
			centimeters.  Unacceptable grabs included those:  containing
			no sediments, which were partially filled or had shelly
			substrates or grossly slumped surfaces.  Grabs completely
			filled to the top, where the sediment was oozing out of the
			hinged top, were also unacceptable.

			See: Kokkinakis et al. (1994a)

		5.1.11 Sample Collection Method References

			See: Hyland et al. (1996),
				Hyland et al. (1998),
				Kokkinakis et al. (1994b)

		5.1.12 Sample Collection Method Deviations

			None

	5.2  Data Preparation and Sample Processing

		5.2.1 Sample Processing Objective

			Process sediment samples for characterization of
			contaminants and TOC.

		5.2.2 Sample Processing Methods Summary

			5.2.2.1 Field Summary

				NA

			5.2.2.2  Laboratory Summary

				See section 4.3 (Data Set Background Information),
					GERG (1995a, 1995b, 1996, 1997a, 1997b, 1998)

		5.2.3 Sample Processing Method Calibration

			See: GERG (1995a, 1995b, 1996, 1997a, 1997b, 1998)

		5.2.4 Sample Processing Quality Control

			Quality control procedures for the analysis of sediment
			contaminants consisted of: (1) participation in a series of
			intercalibration exercises (minimum of two intercalibrations
			per year for metals and three intercalibrations per year for
			organics);  (2) continuous checks on analytical precision and
			accuracy from the analysis of Standard Reference Materials
			(SRMs) with each batch of samples;  (3) initial and ongoing
			instrument calibration checks (ongoing checks performed
			minimally at the middle and end of each sample batch);
			(4) analysis of laboratory reagent blanks (one with each
			sample batch);  (5) analysis of laboratory fortified sample
			matrix spikes and laboratory fortified sample matrix
			duplicates;  (6) analysis of sample duplicates in ~ 10% of the
			samples;  and (7) analysis of internal surrogate and injection
			standards with each sample.  With respect to the analysis of
			SRMs, if analytical results deviated by more than ( 20% from
			the certified values for metals, or by more than ( 30% for the
			organics in the SRM, then a re-analysis of those samples was
			required.  These procedures are consistent with the general
			quality control requirements of both EMAP-E (Heitmuller and
			Valente 1993, see Table 5-4 therein) and the NOAA National
			Status and Trends Program (Lauenstein and Cantillo 1993).

			Portions of the TOC samples, one for each batch of 25 or
			fewer samples, were run in duplicate as tests of analytical
			precision.  Measurement differences could not exceed 20%.
			Quality control procedures for TOC also included the analysis
			of acetanalide standards and certified reference sediments.

			The following QA codes, stored under the variable QA,
			flag QA issues in the sediment and tissue chemistry data
			sets.  Note that all values reported in the CP_CHM_D.DAT
			data set that do not have any QA codes assigned, met all
			QA/QC guidelines and are acceptable without further
			qualification.

		---------------------------------------------------------------
		 QA    Description
		---------------------------------------------------------------

		 ND    Non Detect - Indicates that the concentration of an
		       analyte was too low to detect.  In these cases, the
		       QA code of ND is used, and the concentration is
		       reported as 0.  Although the actual concentration is
		       unknown (but likely very low to none), reporting a
		       concentration of 0 serves as a place holder.

		  J    Just Detected - Indicates that an analyte was detected
		       in the sample, but at a concentration below the method
		       detection limit for the sample.  In these cases, you can
		       be confident that the analyte is present in the sample,
		       but there is a high degree of uncertainty in the reported
		       concentration.  Therefore, values flagged with the J
		       QA code should be considered estimates only, and used
		       with discretion.

		 SC-B  Just Detected - Indicates that an analyte was detected
		       in the sample, but at a concentration below the method
		       detection limit for the sample.  In these cases, you can
		       be confident that the analyte is present in the sample,
		       but there is a high degree of uncertainty in the reported
		       concentration.  Therefore, values flagged with the J
		       QA code should be considered estimates only, and used
		       with discretion.

		  M    Matrix Interference - Indicates that the reported
		       concentration is questionable due to interference from
		       other compounds in the sample.  Therefore, values
		       flagged with the M QA code should be used with
		       discretion.

		  Q    QA problem - Indicates cases where required quality
		       assurance guidelines were not met by the lab.  If no
		       concentration is reported, then the QC problem was
		       judged to be severe enough to invalidate the result
		       for that analyte.  If however a concentration is
		       reported for an analyte with a Q code, then the overall
		       data quality was judged to be reliable enough to be used
		       with discretion.

		D or d Dilution Required - Indicates the sample required
		       dilution prior to analysis.  This has no effect on
		       reported concentrations and is not a problem.
		       Values with this code can be used with no further
		       qualification.

		 AL-P  Algae Present - Indicates that the presence of algae
		       in the sample prevented accurate measurement of TOC.
		       Samples with the AL-P code will have a missing value
		       for TOC.

		  B    Blank Interference - Indicates that their was an
		       interference detected in the blank which would
		       interfere with the accurate determination of an
		       analytes concentration.  Results for observations
		       with the B code should be considered questionable
		       and used with discretion.

		---------------------------------------------------------------

			See: 	Hyland et al. (1996),
				Hyland et al. (1998),
				Kokkinakis et al. (1994a),
				GERG (1995A, 1995B, 1996, 1997A, 1997B, 1998)

		5.2.5 Sample Processing Method Reference

			See: Hyland et al. (1996),
				Hyland et al. (1998),
				Kokkinakis et al. (1994b),
				Section 4.3 (Data Set Background Information)
				Standard Operating Procedures of the Geochemical and
				Environmental Research Group of Texas A&M University,
				GERG (1995A, 1995B, 1996, 1997A, 1997B, 1998)

		5.2.6 Sample Processing Method Deviations

			See: GERG (1995A, 1995B, 1996, 1997A, 1997B, 1998)


6.  DATA ANALYSIS AND MANIPULATIONS

	6.1 Name of New or Modified Value

		The following analytes (ANAL codes) were not measured directly.
		These values are summary valuse calculated from the
		concenterations of several individually measured analytes:
		TOT_PAH, CHLORDAN, TOT_ALKA, TOT_BHC, TOT_PCB, TOT_DDT

	6.2 Data Manipulation Description

		TOT_PAH = Total PAHs

			Sum of 38 PAHs (not including perylene)
			[ACENTHE, ACENTHY, ANTHRA, BENANTH, BENAPY, BENEPY, BENZOBFL,
			BENZOKFL, BGHIPERY, BIPHENYL, C1CHRYSN, C1DIBENZ, C1FLUORA,
			C1FLUORE, C1NAPH, C1PHENAN, C2CHRYSN, C2DIBENZ, C2FLUORE,
			C2NAPH, C2PHENAN, C3CHRYSN, C3DIBENZ, C3FLUORE, C3NAPH,
			C3PHENAN, C4CHRYSN, C4NAPH, C4PHENAN, CHRYSENE, DIBENZAH,
			DIBENZO, FLUORANT, FLUORENE, INDENO, NAPH, PHENANTH, PYRENE]

		CHLORDAN = Total Chlordane

			Sum of Alpha-, Gamma-, and Oxy- chlordane
			[ALPHACHL, GAMMACHL, OXYCHL]

		TOT_ALKA = Total Alkanes

			Sum of 27 Aliphatic Hydrocarbons
			[C10_ALKA, C11_ALKA, C12_ALKA, C13_ALKA, C14_ALKA,
			C15_ALKA, C16_ALKA, C17_ALKA, C18_ALKA, C19_ALKA,
			C20_ALKA, C21_ALKA, C22_ALKA, C23_ALKA, C24_ALKA,
			C25_ALKA, C26_ALKA, C27_ALKA, C28_ALKA, C29_ALKA,
			C30_ALKA, C31_ALKA, C32_ALKA, C33_ALKA, C34_ALKA,
			PHYTANE, PRISTANE]

		TOT_BHC = Total BHC

			Sum of Alpha BHC, Beta BHC, Delta BHC, and
			Gamma BHC (lindane)
			[ALPHABHC, BETABHC, DELTABHC, LINDANE]

		TOT_DDT = Total DDTs

			Sum of 2,4'DDD, 4,4'DDD, 2,4'DDE, 4,4'DDE,
			2,4'DDT, and 4,4'DDT
			[DDD_24, DDD_44, DDE_24, DDE_44, DDT_24, DDT_44]

		TOT_PCB = Total PCBs

			(Sum of (18 PCB congeners - any interferences) * 2.19) + 2.19
			[PCB8, PCB18, PCB28, PCB44, PCB52, PCB66, PCB101,
			PCB105, PCB118, PCB128, PCB138, PCB153, PCB170, PCB180,
			PCB187, PCB195, PCB206, PCB209]

	6.3 Data Manipulation Examples


7.  DATA DESCRIPTION

	7.1 Description of Parameters

		--------------------------------------------------------------
		Variable Type Format   Label
		--------------------------------------------------------------
		STA_NAME Char  7.      Carolinian Province Office Station Name
		DATE     Num  YYMMDD6. Sample collection date (YYMMDD)
		ANAL     Char  8.      Carolinian Province Office analyte code
		CONC     Num  12.3     Analyte concentration (dry wt.)
		UNIT     Char  8.      CONC units
		QA       Char  4.      Quality assurance code
		DETLMT   Num  12.3     Method detection limit
		--------------------------------------------------------------

		Note the conventions used in the Format column above:

			For character (Char) variables, the number given is the
			maximum width (number of characters) for that variable.

			For numeric (Num) variables, the format is given in W.D
			format, where W = maximum width (number of characters)
			for the number (including all digits and the decimal
			point), and D = number of digits to the right of the
			decimal point.

		7.1.6  Precision to which values are reported

			Variables CONC, and DETLMT are reported to 0.001 units.
			However, the precision of the vaules reported are analyte
			dependent as follows:

			------------------------
			Analyte Type   Precision
			------------------------
			TOC            0.01
			Aromatic HCs   0.1
			Aliphatic HCs  0.1
			Pesticides     0.01
			PCBs           0.01
			Butyltins      0.01
			Trace Metals
			   Ag          0.01
			   Al          1
			   Cd          0.001
			   Cu          0.01
			   Mn          0.1
			   Ni          0.1
			   Pb          0.1
			   Se          0.01
			   Si          1
			   Sn          0.01
			   Zn          0.1
			   As          0.01
			   Cr          1
			   Fe          1
			   Sb          0.01
			   Tl          0.01
			   Hg          0.001
			------------------------

			Also note that the following QA codes associated with some
			observations may effect precision:

			ND (Non Detect) - Indicates that the concentration of an
			analyte was too low to detect.  In these cases the
			concentration is reported as 0.  Although the actual
			concentration is unknown (but likely very low to none),
			reporting a concentration of 0 serves as a place holder.

			J (Just Detected) - Indicates that an analyte was detected
			in the sample, but at a concentration below the method
			detection limit for the sample.  In these cases, you can
			be confident that the analyte is present in the sample,
			but there is a high degree of uncertainty in the reported
			concentration.  Therefore, values flagged with the J
			QA code should be considered estimates only, and used
			with discretion.

		7.1.7 Minimum Value in Data Set

			------------------
			Variable   Minimum
			------------------
			CONC         0.000
			DETLMT       0.000
			------------------

		7.1.8 Maximum Value in Data Set

			-------------------
			Variable    Maximum
			-------------------
			CONC     536950.040
			DETLMT    10000.000
			-------------------

	7.2 Data Record Example

		7.2.1 Column Names for Example Records

			CP_CHM_D.DAT

				STA_NAME;DATE;ANAL;CONC;UNIT;QA;DETLMT

			CP_CHM_A.DAT

				ANAL;A_NAME

			CP_CHM_Q_DAT

				Contains descriptive text not formatted as a data set.

		7.2.2 Example Data Records

			CP_CHM_D.DAT

				CP94001;940815;ACENTHE;0.070;ng/g;J;5.000
				CP94001;940815;ACENTHY;0.210;ng/g;J;5.000
				CP94001;940815;AG;0.030;ug/g; ;0.010
				CP94001;940815;AL;9843.901;ug/g; ;355.000
				CP94001;940815;ALDRIN;0.039;ng/g;J;0.100
				CP94001;940815;ALPHABHC;0.000;ng/g;ND;.
				CP94001;940815;ALPHACHL;0.000;ng/g;ND;0.100

			CP_CHM_A.DAT

				ACENTHE;Acenaphthene
				ACENTHY;Acenaphthylene
				AG;Silver
				AL;Aluminum
				ALDRIN;Aldrin
				ALPHABHC;Alpha HCH (Alpha BHC)


8.  GEOGRAPHIC AND SPATIAL INFORMATION

	8.1 Minimum Longitude

		-81 Degrees, 43.83 Minutes West Longitude

	8.2 Maximum Longitude

		-75 Degrees, 33.82 Minutes West Longitude

	8.3 Minimum Latitude

		27 Degrees, 12.07 Minutes North Latitude

	8.4 Maximum Latitude

		36 Degrees, 43.43 Minutes North Latitude

	8.5 Name of area or region	

		Coastal distribution of sampling is along the southeastern US
		from Cape Henry, VA, through St. Lucie Inlet, FL.  States
		represented:  Virginia, North Carolina, South Carolina, Georgia,
		and Florida.


9.  QUALITY CONTROL/QUALITY ASSURANCE

	9.1 Measurement Quality Objectives

			See: Hyland et al. (1996),
				Hyland et al. (1998),
				Kokkinakis et al. (1994a)

	9.2 Quality Assurance/Control Methods

		See section 5.2.4 (Sample Processing Quality Control) above,
			GERG (1995A, 1995B, 1996, 1997A, 1997B, 1998)

	9.3 Quality Assessment Results

		Unless flagged by one of the QA codes defined in section
		5.2.4 (Sample Processing Quality Control), or specifically
		mentioned in GERG (1995A, 1995B, 1996, 1997A, 1997B, 1998),
		all data reported in the CP_CHM_D.DAT data set met the QA/QC
		guidelines given above and are acceptable without further
		qualification.


10. DATA ACCESS

	10.1 Data Access Procedures

		Data can be downloaded from the WWW site. 

	10.2 Data Access Restrictions

		Data can only be accessed from the WWW site.

	10.3 Data Access Contact Persons

		Dr. Jeffrey L. Hyland, Carolinian Province Manager
		NOAA/NOS/ORCA/CMBAD
		NOAA/EPA Joint Nat. Coastal Research and Monitoring Program
		217 Fort Johnson Rd. (P.O. Box 12559)
		Charleston, SC 29422-2559
		(843)762-5415 (Tel.)
		jeff.hyland@noaa.gov (e-mail)

		Len Balthis, Statistician
		PTSI
		217 Fort Johnson Rd (P.O. Box 12559)
		Charleston, SC 29422-2559
		843-762-5652 (Tel.)
		843-762-5110 (FAX )
		balthisl@cofc.edu (e-mail)

		Data Librarian, EMAP-Estuaries
		Melissa M. Hughes
		OAO Corporation
		U.S. EPA NHEERL-AED
		27 Tarzwell Drive
		Narragansett, RI  02882-1197
		(401) 782-3184 (Tel.)
		(401) 782-3030 (FAX)
		hughes.melissa@epamail.epa.gov (e-mail)

	10.4 Data file Format

		Delimited ASCII Text

	10.5 Information Concerning Anonymous FTP

		Not accessible

	10.6 Information Concerning Gopher and WWW

		Data can be downloaded from the WWW.

	10.7 EMAP CD-ROM Containing the Data file

		Data not available on CD-ROM.


11.  REFERENCES

	Balthis, W.L., J.L. Hyland, and T.R. Snoots.  1998.  Compendium of
		environmental data for estuaries sampled in the North Carolina
		portion of the EMAP Carolinian Province during summer 1994-1996.
		Unpublished report, May 1998.  62 p.

	GERG. 1995a.  Analytical Report, EMAP Near Coastal -
		Carolinian Province 1994.  Texas A&M University - Geochemical
		and Environmental Research Group, College Station, TX.

	GERG. 1995b.  EMAP Carolinian 1994 Final Sediment Trace Element Data
		Report.  Texas A&M University - Trace Element Research Laboratory,
		College Station, TX.

	GERG. 1996.  Carolinian Province EMAP project, 1995 sediment samples.
		Analytical report No. 5C688-A.  Texas A&M University - Geochemical
		and Environmental Research Group, College Station, TX.

	GERG. 1997a.  Carolinian Province EMAP project, 1995 sediment samples.
		Analytical report No. 5C688-B.  Texas A&M University - Geochemical
		and Environmental Research Group, College Station, TX.

	GERG. 1997b.  Carolinian Province EMAP project, 1996 sediment samples.
		Analytical report No. 6A058-A.  Texas A&M University - Geochemical
		and Environmental Research Group, College Station, TX.

	GERG. 1998.  Carolinian Province EMAP project, 1997 sediment samples.
		Analytical report No. 79385-A.  Texas A&M University - Geochemical
		and Environmental Research Group, College Station, TX.

	Heitmuller, P.T. and R. Valente. 1993. EMAP - Estuaries Louisianian
		Province - 1993 Quality Assurance Project Plan. U.S. EPA
		Environmental Research Laboratory, Gulf Breeze, FL.

	Hyland, J.L., T.J. Herrlinger, T.R. Snoots, A.H. Ringwood, R.F.
		Van Dolah, C.T. Hackney, G.A. Nelson, J.S. Rosen, and S.A.
		Kokkinakis.  1996.  Environmental quality of estuaries of the
		Carolinian Province: 1994. Annual statistical summary for the
		1994 EMAP-Estuaries Demonstration Project in the Carolinian
		Province.  NOAA Technical Memorandum NOS ORCA 97.  NOAA/NOS,
		Office of Ocean Resources Conservation and Assessment,
		Silver Spring, MD. 102 p.

	Hyland, J.L., L. Balthis, C.T. Hackney, G. McRae, A.H. Ringwood,
		T.R. Snoots, R.F. Van Dolah, and T.L. Wade.  1998.
		Environmental quality of estuaries of the Carolinian Province:
		1995.  Annual statistical summary for the 1995 EMAP-Estuaries
		Demonstration Project in the Carolinian Province.  NOAA Technical
		Memorandum NOS ORCA 123  NOAA/NOS, Office of Ocean Resources
		Conservation and Assessment, Silver Spring, MD.

	Kokkinakis, S.A., C. Mageau, and A. Robertson.  1994a.  Carolinian
		Demonstration Project - 1994 Quality Assurance Project Plan.
		Joint National Status and Trends/Environmental Monitoring and
		Assessment Program.  NOAA/NOS/ORCA, Silver Spring, MD.

	Kokkinakis, S.A., J.L. Hyland, and A. Robertson.  1994b.  Carolinian
		Demonstration Project - 1994 Field Operations Manual.  Joint
		National Status and Trends/Environmental Monitoring and
		Assessment Program.  NOAA/NOS/ORCA, Silver Spring, MD.

	Lauenstein, G.G. and A.Y. Cantillo (eds.). 1993. Sampling and
		analytical methods of the National Status and Trends Programs,
		National Benthic Surveillance and Mussel Watch Projects, 19841992.
		NOAA Technical Memorandum, NOS ORCA 71.

	Salonen, K. 1979. A versatile method for the rapid and accurate
		determination of carbon by high temperature combustion. Limnol.
		Oceanogr., 24: 177183.

	Strobel, C.J., S.J. Benyi, D.J. Keith, H.W. Buffum, and E.A.
		Petrocelli. 1994. Statistical summary: EMAP - Estuaries
		Virginian Province - 1992. U.S. EPA Office of Research
		and Development, Environmental Research Laboratory, Narragansett,
		RI. EPA/620/R-94/019.

	Summers, J.K., J.M. Macauley, P.T. Heitmuller, V.D. Engle, A.M. Adams,
		and G.T. Brooks. 1993. Annual statistical summary: EMAP -
		Estuaries Louisianian Province - 1991. U.S. EPA Office of
		Research and Development, Environmental Research Laboratory,
		Gulf Breeze, FL. EPA/600/R-93/001.

	Taylor, B.J. and B.J. Presley. 1993. GERG trace element quantification
		techniques. In: G.G. Lauenstein and A.Y. Cantillo (eds.). Sampling
		and analytical methods of the National Status and Trends Programs,
		National Benthic Surveillance and Mussel Watch Projects, 1984-1992.
		NOAA Technical Memorandum, NOS ORCA 71.

	U.S. EPA.  1995.  Environmental Monitoring and Assessment Program
		(EMAP): Laboratory Methods Manual-Estuaries, Volume 1: Biological
		and Physical Analyses.  U.S. Environmental Protection Agency,
		Office of Research and Development, Narragansett, RI.
		EPA/620/R-95/008.

	Wade, T.L., J.M. Brooks, M.C. Kennicutt II, T.J. McDonald, J.L. Sericano,
		and T.J. Jackson. 1993. GERG trace organics contaminant analytical
		techniques. In: G.G. Lauenstein and A.Y. Cantillo (eds.). Sampling
		and analytical methods of the National Status and Trends Programs,
		National Benthic Surveillance and Mussel Watch Projects, 1984-1992.
		NOAA Technical Memorandum, NOS ORCA 71.

	Wade, T.L., B. Garcia-Romero, and J.M. Brooks. 1990. Butyltin in sediments
		and bivalves from U.S. coastal areas. Chemosphere, 20: 647-662.

	Wade, T.L., D.J. Velinsky, E. Reinharz, and C.E. Schekat. 1994. Tidal
		river sediments in the Washington, D.C. area. II. Distribution and
		sources of organic contaminants. Estuaries, 17: 321-333.


12.  TABLE OF ACRONYMS

	C		Degrees Celsius
	cc		Cubic centimeters
	cm2		Square centimeters
	CMBAD		Coastal Monitoring and Bioeffects Assessment Division
	CU		Clemson University
	EMAP		Environmental Monitoring and Assessment Program
	EPA		U.S. Environmental Protection Agency
	EPA-AED		EPA-Atlantic Ecology Division
	EPA-GED		EPA-Gulf Ecology Division
	EPA-RTP		EPA-Research Triangle Park, NC
	FLDEP		Florida Dept. of Environmental Protection
	FMRI		Florida Marine Research Institute
	FTP		File Transfer Protocol
	GIS		Geographical Information System
	JCWS		Johnson Controls Word Services
	km2		Square kilometers
	m2		Square meters
	mg/L		Milligrams per liter
	mS/cm		MilliSiemens per centimeter (equiv. to millimhos/cm)
	MRRI		Marine Resources Research Institute
	NCNERR		North Carolina National Estuarine Research Reserve
	NCSU		North Carolina State University, NC
	NA		Not Applicable
	ng/g		Nanograms per gram
	NOAA		National Oceanic and Atmospheric Administration
	NOS		National Ocean Service
	ORCA		Office of Ocean Resources Conservation and Assessment
	QA/QC		Quality Assurance/Quality Control
	ppb		Parts per billion (equiv. to ng/g)
	ppm		Parts per million (equiv. to ug/g)
	ppt		Parts per thousand
	SAIC		Science Applications International Corporation
	SCDNR		South Carolina Dept. of Natural Resources
	TOC		Total Organic Carbon
	TAMU/GERG		Texas A&M University, Geochemical and Environmental
			Research Group
	TPMC		Technology Planning and Management Corporation
	ug/g		Micrograms per gram
	um		Micrometers
	UC		University of Charleston, SC
	UGA		University of Georgia, GA
	UNC-W		University of North Carolina - Wilmington, NC
	USGS-GB		US Geological Survey - Gulf Breeze, FL
	wt.		Weight
	WWW		World Wide Web -Internet


13.  PERSONNEL INFORMATION

	Dr. Courtney T. Hackney
	University of North Carolina - Wilmington,
	Wilmington, NC

	Melissa M. Hughes
	Data Librarian, EMAP-Estuaries
	OAO Corporation
	U.S. EPA NHEERL-AED
	27 Tarzwell Drive
	Narragansett, RI  02882-1197
	(401) 782-3184 (Tel.)
	(401) 782-3030 (FAX)
	hughes.melissa@epamail.epa.gov (e-mail)

	Dr. Jeffrey L. Hyland
	Carolinian Province Manager
	NOAA/NOS/ORCA/CMBAD
	NOAA/EPA Joint Nat. Coastal Research and Monitoring Program
	217 Fort Johnson Rd. (P.O. Box 12559)
	Charleston, SC 29422-2559
	(843)762-5415 (Tel.)
	(843)762-5110 (FAX)
	jhyland@rdc.noaa.gov (e-mail)

	Steven A. Kokkinakis
	Carolinian Province QA Officer
	NOAA/NOS/ORCA/CMBAD
	N/ORCA 2, SSMC #4, WS#10502
	1305 East-West Highway
	Silver Spring, MD 20910-3281
	(301)713-3028 Ext. 171 (Tel.)
	(401)713-4388 (FAX)
	skokkinakis@rdc.noaa.gov (e-mail)

	Len Balthis, Statistician
	PTSI
	217 Fort Johnson Rd (P.O. Box 12559)
	Charleston, SC 29422-2559
	843-762-5652 (Tel.)
	843-762-5110 (FAX )
	balthisl@cofc.edu (e-mail)

	Jan Landsberg
	Florida Dept. of Environmental Protection
	Florida Marine Research Institute
	St. Petersburg, FL

	James McKenna
	Florida Dept. of Environmental Protection
	Florida Marine Research Institute
	St. Petersburg, FL

	Dr. Gil McRae
	Florida Dept. of Environmental Protection
	Florida Marine Research Institute
	St. Petersburg, FL

	Gary A. Nelson
	Florida Dept. of Environmental Protection
	Florida Marine Research Institute
	St. Petersburg, FL

	Dr. Amy H. Ringwood
	South Carolina Dept. of Natural Resources,
	Marine Resources Research Institute
	Charleston, SC

